PTS members benches

Discussion on general flowbench design
Post Reply
blaktopr
Posts: 622
Joined: Sat Feb 20, 2010 9:27 pm
Location: Central NJ
Contact:

PTS members benches

Post by blaktopr »

I was thinking of this for current and future board members. Giving a small pic with a description and maybe a link to the old forum where the build was (if it is there), or the new one. This may help others get an idea of what direction to take, personal or PTS plans without extensive surfing or questions. If there is something that stands out for someone, it can be discussed in the appropriate section. Plus it gives a place to showcase each person's hard work. Good or bad idea??
Chris Sikorski
Chris@wetflowtech.com
Totallywirednow.com
blaktopr
Posts: 622
Joined: Sat Feb 20, 2010 9:27 pm
Location: Central NJ
Contact:

Re: PTS members benches

Post by blaktopr »

Something like this....

Personal built bench
http://www.tractorsport.com/cgi-bin/for ... T;f=9;t=48
Orifice plate design
10 Surplus motors
600+CFM@28"
PTS orifice plates
PTS Computer with Flowsoft
PTS velocity probe
PTS Check valves
This is a high capacity flowbench built with a steel skeleton. Direction changes are done with Becksom ports. The piece to the right is the wetflow attachment. It is also used as a workbench.
flowbenchpic.jpg
You do not have the required permissions to view the files attached to this post.
Chris Sikorski
Chris@wetflowtech.com
Totallywirednow.com
Hotz
Posts: 709
Joined: Thu Feb 25, 2010 10:37 pm

Re: PTS members benches

Post by Hotz »

blaktopr wrote:Something like this....

Personal built bench
http://www.tractorsport.com/cgi-bin/for ... T;f=9;t=48
Orifice plate design
10 Surplus motors
600+CFM@28"
PTS orifice plates
PTS Computer with Flowsoft
PTS velocity probe
PTS Check valves
This is a high capacity flowbench built with a steel skeleton. Direction changes are done with Becksom ports. The piece to the right is the wetflow attachment. It is also used as a workbench.
flowbenchpic.jpg
Could you explain doors Beckson?(pics)
Hotz :?:
Sorry my english mistakes.
PTS Parts>> http://www.flowbenchtech.com/store.html
blaktopr
Posts: 622
Joined: Sat Feb 20, 2010 9:27 pm
Location: Central NJ
Contact:

Re: PTS members benches

Post by blaktopr »

Hotz,
The 2 large white Becksoms access the measuring plates.
The left white Becksom also access the two 6" Becksoms inside the bench to change directions.
The 4 brown Becksoms also control direction but for the motors. The top two are open during intake testing, the two bottom two open for exhaust testing.
There are pictures of inside the bench before the modification at the link I posted above.
Chris Sikorski
Chris@wetflowtech.com
Totallywirednow.com
Hotz
Posts: 709
Joined: Thu Feb 25, 2010 10:37 pm

Re: PTS members benches

Post by Hotz »

Thanks Chris

Hotz :D
Sorry my english mistakes.
PTS Parts>> http://www.flowbenchtech.com/store.html
turbodart
Posts: 2
Joined: Fri Sep 10, 2010 5:08 pm

Re: PTS members benches

Post by turbodart »

heres my "barracuda"! 7 motors from vacuum cleaners found around. maxes out at 300cfm@28". fully digital,with custom made triacs to adjust speed on the motors!

just about to build another one, with more space to more motors!
Thanx to bruce for making this affordable!

up for testing and porting is a pair of RHS-magnum heads! going on a 408 stroker, got em up in the 275cfm area before the valve-job.
Image


have a nice day,

BR Daniel,Norway
Flash
Posts: 773
Joined: Thu Feb 25, 2010 3:39 pm

Re: PTS members benches

Post by Flash »

Nice to have another Mopar Man around here. ;)

heard lots Good about the RHS!

How are the air speed down the middle of the port at 275 cfm?.........What intake valve?

If you get a chance, would like to see the intake floor on that RHS head.

Also curious about that valve lift fixture in the picture.

By the way welcome aboard :!:
Gordon
turbodart
Posts: 2
Joined: Fri Sep 10, 2010 5:08 pm

Re: PTS members benches

Post by turbodart »

I did not test it then, had no probe, but I have a set of EQ magnums who are wery similar, and I like them alot! I have a screen-shot of a program I have developed! I hope you understand the numbers. at this stage I'm not finishet with the port-work, only spent a few hours on the head! easy head to make good-flowing! :D
Image
msj442
Posts: 18
Joined: Wed Mar 03, 2010 11:33 pm

Re: PTS members benches

Post by msj442 »

now that is a freggin nice flow sheet. i especially like the pics to get the customer involved and familiar with whats going on. are you offering this for sale or anything? if so can you pm me or emil me at jtldad@yahoo.com
my visits are a little less frequent these days.

max
Post Reply